Higher Colleges of Technology Abu Dhabi Men’s CollegeEng 307...

Question

Higher Colleges of Technology Abu Dhabi Men’s College Eng 307 Mechanical Engineering Major related report 30% Student Brief LSEC N307 As part of the course you are required to do a report of 1000...

1 answer below »

Higher Colleges of Technology

Abu Dhabi Men’s College
Eng 307 Mechanical Engineering
Major related report 30%

Student Brief LSEC N307
As part of the course you are required to do a report of 1000 words. The preliminary report accounts for 16% and is 800 words with a minimum of 4 references. The extended report is 14% and 1000 words with a minimum of 8 references. Your report can be +10% without penalty.

Your report will count for 30% of your overall course grade.

You should do an extensive amount of research for your report. After your preliminary draft you will be given feedback to improve your paper.

You must submit your report to SafeAssign in BB Vista and upload your preliminary and extended reports to BB Vista in the Assignments sections.

Due dates on course calendar.

Preliminary report: November 22^nd
Extended report: December 13^th

Late papers will be penalized. This means you will only receive a maximum of 60% (sixty percent) of your total Project grade if you submit after the due date.

LSEC N307 Project Information Week. 9
Which developments within [mechanical engineering] your major have the most potential for the future? Give justifications and reasons for your choice. Explain how the developments may be applied in the UAE and/or other countries.

Word Count & References
1,000 words total excluding references.
You should include a total of 4 x references in the Draft Project + 4 x references in the Final Project = 8 x references total in the Final Project. Your references must include at least 1 book, 1 website, 1 newspaper article and 1 journal article.
Project Sections
Introduction = 125 w.
Introduce your topic. Provide a background to the topic. Explain briefly what you will say in your essay.
Main Body Parag. 1 = 250 w.
Which developments within [mechanical engineering] / your major have the most potential for the future? = Explain which specific topic area within your major is especially interesting in terms of future plans for development and provide evidence from the literature (= references) to support your ideas.
Main Body Parag. 2 = 250 w.
Give justifications and reasons for your choice. = Explain why you have selected this topic and provide evidence from the literature (= references) to support your ideas.
Main Body Parag. 3 = 250 w.
Explain how the developments may be applied in the UAE and/or other countries = Explain how these future developments can be applied to the UAE / your chosen country/ies and provide evidence from the literature (= references) to support your ideas.
Conclusion = 125 w.
Say what you have said. In the conclusion you should summarise the key points you have discussed in your Main Body Parts 1-3. You do not need references in this section.
Word Count = 1,000 w. total
Minimum = 990 words (less than 990 will receive a maximum of 60%)
Maximum = 1,010 words (more than 1,010 will receive a maximum of 60%)

005_ujebzk-fnd0pyhn.docx

Answered Same Day Dec 21, 2021

Robert · Accepted Answer

Introduction: 
Oil pumps are a critical part of an automotive system. Lubricating oil is fed by a 
pump through pipes or ducts to different mating parts of an engine to slow down wear 
and tear due to friction between metal parts and for possible heat displacement. The type 
of oil pump used in an automotive engine depends on the engine structure, the type of 
drive and its lubrication requirements. In an oil burning plant the oil must be filtered and 
be subjected to a stable pressure of higher order. The oil flow in a burner 
plant/automotive system must start and stop accurately in step with the requirements 
made on it. The oil pump must be so designed to carry out these functions.
There are many types of pumps used in industries based on need and application, 
to explain a few Centrifugal pumps, Piston pumps, Gear pumps etc., Centrifugal pumps 
are mainly used to circulate liquid for example, hot water in a central heating system. 
This type of pump is not self-priming. Liquid enters at the centre of the pump and is flung 
by the rotating impeller out to the walls of the pump housing. In this way pressure is built 
up at the outlet of the pump. Piston pumps are used to transport liquid where a particular 
high pressure is required at the pump outlet. An example is where feed water must be 
supplied to a steam boiler. As and when, the piston travels upwards the water above it 
will be forced into the boiler. At the same time, the suction created below the piston 
sucks water from the condensed water tank into the pump. When the piston travels 
downwards the flap valve lifts and water flows into the space above the piston so that the 
pumping process can be repeated at the next stroke of the pump. Gear pumps are used 
where good suction and good pressure characteristics are required for example in an oil 
burning plant.

Higher Colleges of Technology Abu Dhabi Men’s College Eng 307 Mechanical Engineering Major related report 30% Student Brief LSEC N307 As part of the course you are required to do a report of 1000...

Solution

Answer To This Question Is Available To Download

Related Questions & Answers

Submit New Assignment