Lab 6 - Hooke's Law
XXXXXXXXXXName:________________
Objectives:
· Validate Hooke’s Law
· Use Hooke’s Law to determine unknown masses and an unknown value.
· Analyze how different combinations of spring affect the stretching of a system.
Background:
Hooke's law states that extension of a spring is proportional to applied force.
If a spring obeys Hooke's law, then a graph of applied force against extension will be a straight line, whose gradient (slope) is k:
The equation of the straight line is:
where:
= stretching force applied to the spring
= spring constant
= extension of the spring
Part 1: Validating Hooke’s Law
Open the following simulator and click the lab option:
https:
phet.colorado.edu/sims/html/masses-and-springs/latest/masses-and-springs_en.html
a) Place the 100g mass onto the spring. The spring will begin to oscillate up and down. Stop this by clicking on the mass several times or increasing the ‘Damping’ value to ‘Lots’.
) Click the ‘Displacement’ and ‘Movable Line’ options on the right. Adjust the movable red line to the tip of the green a
ow.
c) Use the ruler tool (the units are in mm) on the bottom right to measure the extension of the spring with the 100g mass. Convert this mass to a weight (use ) and add this data to table 1. Remember to convert g to kg.
Mass added (g)
Weight (N)
Extension (mm)
100g
Table 1
d) Using the slider at the top, change the mass and record 5 more results of weight and extension. Add your results to table 1.
e) Plot a graph (either on paper or using Excel) for Force (y-axis) against extension (x-axis). Draw a line of best fit through your points.
f) Using your graph, determine the spring constant of your spring (in ) by finding the gradient.
g) What evidence from your graph shows that the spring obeys Hooke’s Law?
Part 2: Determining Unknown Masses
Using your value for the spring constant in part 1, determine the masses of the two unknown, red and blue masses in the simulation. Show your working and measurements taken for this part. To get a good average result, at least 3 measurements should be taken of each mass.
ed mass = .......... XXXXXXXXXXg
lue mass = ............ XXXXXXXXXXg
Part 3: Determining Unknown Value of Gravity
Change the ‘Gravity’ to ‘Planet X’.
The value of is no longer but something unknown.
Using your spring constant from part 1, determine the unknown value of for this planet. Show your working and measurements taken for this part. To get a good average result, at least 3 measurements should be taken of each mass.
unknown = ......................................
Part 4: Analysing Systems of Springs
Open the simulation below and press the systems open:
https:
phet.colorado.edu/sims/html/hookes-law/latest/hookes-law_en.html
a) Select the options ‘Displacement’, ‘Equili
ium Potion’ and ‘Values’. Make sure the option of two springs in parallel is selected so that the springs look like the setup in the image below.
) Keep the top spring constant and the bottom spring constant . Apply 100N of force to the right. Measure the extension and determine the total spring constant of the two springs in parallel (). Record your results in table 2.
Two Springs in Parallel
(
(
F (N)
Extension (m)
Total (
100 N
100 N
100 N
100 N
Table 2
c) Repeat step b) three more times by changing the values of and and adding the results to table 2.
d) Describe the relationship between the individual spring constants and , and the total spring constant for springs in parallel. Try and write this in the form of an equation.
e) Press the series spring button so that the springs change their combination to look like the setup in the image below:
f) Keep the left spring constant and the right spring constant . Apply 100N of force to the right. Measure the extension and determine the total spring constant of the two springs in series (). Record your results in table 3.
Two Springs in Series
(
(
F (N)
Extension (m)
Total (
100 N
100 N
100 N
100 N
Table 3
g) Repeat step f) three more times by changing the values of and and adding the results to table 3.
h) Three students offer a model for finding the total spring constant for two springs in series:
· Student 1:
· Student 2:
· Student 3:
Explain which student’s model is co
ect based on your results.